Power Quality Problems in Industrial Units: Harmonics, Sags and Power Factor
Navyashree Engineers Private Limited ·
Power quality problems often show up as other problems: equipment that trips for no clear reason, drives that fault, motors that run hot, lights that flicker, or electricity bills that do not match expectations. Because the symptoms look like many other faults, a structured measurement is usually the way to find the cause.
This guide explains the common problem types and how a study is normally approached. It does not diagnose your site.
The common problem types
- Harmonics: Non-linear loads such as variable speed drives, UPS systems, rectifiers and LED drivers draw current in a distorted way. The distortion can heat cables, transformers and motors and can disturb sensitive equipment.
- Voltage sags and swells: Short drops or rises in voltage can come from the supply network or from large loads starting inside the plant. Sensitive controls and drives may trip or reset.
- Voltage imbalance: Unequal voltages across the phases can overheat three-phase motors.
- Flicker: Rapid variations in voltage, often from fluctuating loads, can affect lighting and some processes.
- Poor power factor: A low power factor increases the current needed for the same useful power and can affect charges and the capacity of the supply equipment. Correction equipment needs care where harmonics are present.
- Transients: Short, sharp disturbances from switching events can damage electronics over time.
Signs that a study may be worthwhile
Report to your electrical team if you see repeated nuisance tripping, unexplained drive or controller faults, unusually hot transformers or capacitor banks, failing electronic equipment, or flicker that affects the process. Note when the problem occurs and which equipment is involved, because patterns help the study.
How a study is usually approached
A power quality study normally records electrical parameters over a period using an analyser connected at agreed points. The recording period should cover the normal operating cycles of the plant, since problems may only appear in certain shifts or processes. The results are then reviewed against the loads and the supply conditions.
Ask the team to explain where the measurements will be taken and why, how long the recording will run, which parameters will be captured and how the findings will be presented. A report should link each observation to a location and a time, and should separate measured facts from interpretation.
What to prepare
- Single-line diagrams and the equipment list for the area under study.
- Details of drives, UPS systems, capacitor banks and any recent changes.
- A record of the symptoms, with dates and times where possible.
- Access arrangements for the measurement points, with the safety rules that apply.
Solutions come after the findings
It is tempting to buy a filter or a capacitor bank on the first suspicion. The right remedy depends on the findings. Different problems need different answers, and the wrong equipment can make a harmonic problem worse. Agree that any recommended action will be traced to a specific finding, and decide who will design, supply and commission it.
Keep a baseline
Once the study is complete, keep the report. A later measurement can show whether a change has helped, and the record is useful when new loads are added.
Read more on our power quality testing service, and see how it connects with electrical thermography and electrical maintenance contracts for industrial sites. For installation scope, see industrial electrical contractors.
Navyashree Engineers can discuss a power quality study using your drawings, equipment details, site location and access arrangements. The scope and any follow-up work should be confirmed for your installation. Call +91 99808 37999 or use the contact page to request a site assessment.
Related services
Explore our Super Grade electrical contractors, commercial electrical contractors, industrial electrical contractors, electrical design consultants and HVAC contractors. You can also request a site assessment.
Frequently asked questions
Can you help me compare electrical quotations for my project?
Yes. Share your drawings, equipment schedule and site requirements and our team can review the scope with you. Call +91 99808 37999 or use the contact page to request a site assessment.
Is Navyashree Engineers a licensed electrical contractor?
Yes. Navyashree Engineers is a Government-licensed Super Grade electrical contractor. Licence SGL210314BNG is issued by the Department of Electrical Inspectorate, Government of Karnataka.
Where do you work?
Our head office is in Nagarbhavi, Bengaluru, with a branch office on Vignananagar Main Road. We take enquiries across Bengaluru and Karnataka.
Is this article a quotation or a design?
No. It is general guidance. Scope, equipment and responsibilities are confirmed in the quotation for your project after reviewing drawings and the site.
